Skip to main content
YONEIINNOVATIVE MATERIAL TECH

EV battery materials

CCS Bracket Material Selection: PA66, PPA and PC/ABS

Compare PA66, PPA, PC/ABS and flame-retardant PC for CCS brackets, including V-0, thermal cycling, insulation and dual-85 validation.

10 minUpdated 2026-11-22Reviewed by YONEI R&D Team

Direct answer

There is no universal CCS bracket material. A flame-retardant PC/ABS is a strong starting point when the bracket needs balanced impact, V-0 flame performance, electrical insulation and dual-85 aging. A glass-fiber PA66 may be more appropriate for a highly structural NTC bracket or metal-insert component. PPA and other high-heat families become relevant when continuous temperature or chemical exposure exceeds the practical range of the lower-cost route.

The correct selection starts with the bracket function, wall thickness, failure location and test plan. This guide compares the material routes used in YONEI's EV and energy-storage application page and explains how to qualify them.

Map the bracket architecture

Not every part called a “CCS bracket” carries the same load or electrical role. Separate the assembly into:

  • Main structural brackets
  • NTC holders and sensor supports
  • Battery covers and isolation plates
  • Busbar supports and cell spacers
  • Harness isolation films
  • Insert-molded metal-to-plastic interfaces

The material decision should follow the highest-risk function. A large bracket may be controlled by warpage and insert stress. A thin cover may be controlled by V-0 at the production thickness and dielectric withstand. A sensor holder may be controlled by creep and dimensional stability.

Compare the major material families

Flame-retardant PC/ABS

FR PC/ABS is useful when the part needs a balance of impact, heat, flow, appearance and flame retardancy. YONEI's CFR3010-901510 route is directed at V-0, dual-85 1000 h and a notched impact result above 10 after aging in the referenced project material. The PC component improves heat and toughness relative to standard ABS; the ABS component supports flow and practical molding.

Use FR PC/ABS as the first candidate for CCS brackets and covers when the continuous temperature is within the validated HDT range and the part needs better impact than a highly filled engineering plastic. The relevant PC/ABS blend overview explains the high-flow and thin-wall design considerations.

Glass-fiber PA66

PA66 + 20% GF can provide high rigidity, creep resistance and dimensional control. It is a strong route for NTC brackets, motor structures and insert-molded components. A63V0GV20 is YONEI's V-0, PA66 + 20% GF direction for NTC brackets and related structures.

PA66 absorbs moisture and requires a hydrolysis-resistant package for long wet-heat exposure. The qualification should define conditioning, drying, weld-line strength and dimensional change. The PA66 compound overview compares GF25, GF40, GF50, FR and hydrolysis-resistant directions.

PPA

PPA is relevant when high continuous temperature, strong chemical exposure or high dimensional stability rules out the standard PA66 and PC/ABS routes. It is not automatically better for a CCS bracket: higher stiffness and heat resistance may come with different flow, toughness, cost and processing requirements.

Select PPA only when a defined temperature or chemical condition justifies it, and validate the actual grade at the production thickness.

Flame-retardant PC film

FR PC film is a separate form factor for covers, cell-to-cell isolation and harness separation. CM9610-BKF1 is published with V-0/VTM-0 at 0.5 mm, dual-85 1000 h, CTI 175 V and dielectric strength of at least 35 kV/mm.

Film should not be treated as a thinner version of an injection-molded bracket. Die cutting, creasing, adhesive compatibility, puncture resistance and assembly handling can control the result.

Define the operating requirements

Build a requirement sheet before requesting samples:

  1. Production wall thickness
  2. Continuous and peak temperature
  3. V-0 test thickness and specimen orientation
  4. -40°C to 85°C cycle count
  5. Dual-85 duration
  6. Insulation resistance and withstand voltage
  7. Insert, screw and snap loads
  8. Warpage limit
  9. Flame and electrical test after aging
  10. Annual volume and project timing

Do not compare a V-0 result at 1.5 mm with a drawing that requires 0.8 mm. Do not compare a room-temperature impact value with an aged value on a different specimen.

Build a qualification ladder

Stage 1: Material screening

Review the controlled TDS, color, flame rating, HDT, impact, insulation and aging data. Reject a candidate when the test thickness, standard or grade does not match the requirement.

Stage 2: Molded specimen

Mold plaques and representative ribs. Measure flow, weld-line strength, shrinkage and warpage. Run initial electrical and flame tests.

Stage 3: Aged coupon

Age the production color and thickness under 85°C / 85% RH. Repeat impact, dimensional, visual and electrical tests. Record the failure mode, not only pass/fail.

Stage 4: Full bracket

Test the complete bracket after assembly with inserts, fasteners and adjacent components. Add thermal cycling, vibration, handling and dielectric withstand as required by the battery-pack program.

Avoid four common selection errors

The first error is selecting by polymer name. A PA66 from one supplier may have a completely different hydrolysis package from another.

The second error is using a V-0 result from a thinner or thicker specimen than the production part. Flame performance must match the actual wall and color.

The third error is treating CTI as a complete electrical qualification. Tracking resistance must be combined with insulation resistance, withstand voltage and the final creepage path.

The fourth error is assuming a specimen-level dual-85 result proves the molded bracket. Insert stress and weld lines can change the failure location.

YONEI route summary

For a CCS bracket, begin with the CFR3010-901510 route when balanced impact, V-0 and dual-85 are the key constraints. For an NTC bracket, evaluate A63V0GV20 PA66 + 20% GF. For thin covers and isolation, evaluate CM9610-BKF1 FR PC film. Each route should be confirmed through the EV battery application page, controlled TDS and a part-level validation plan.

The final material should be the lowest-complexity route that passes the complete bracket test plan, not simply the material with the highest headline performance.

Standards and authoritative references

Verify the test method and current standard edition

These links lead to official standards bodies or their public catalogues. YONEI article conclusions should be read with the controlled TDS, current standard edition and project test plan.

  1. 01IEC Webstore — official standards catalogueInternational Electrotechnical Commission · Search the official catalogue for IEC 60112, IEC 60243-1, IEC 60068-2-78 and IEC 62852.
  2. 02UL 94 — Tests for Flammability of Plastic MaterialsUL Standards & Engagement
  3. 03UL 746A — Polymeric Materials: Short Term Property EvaluationsUL Standards & Engagement

Engineering review

Turn the article into a validated material route

Share the part, wall thickness, operating environment and target standard. The YONEI R&D team will map the next material and testing step.

Talk to our R&D engineer

Instant technical inquiry

Engineer available

YONEI

Hello, this is YONEI Innovative Material. What material solution do you need? Leave your requirement and contact details, and our engineer will reply as soon as possible.