01
fatigue + creep
Repeated motion
Joints, motor mounts and connections need stable long-term deformation control.
High flexural modulus
ROBOTICS
Rigidity, toughness and stability for robot structures
Robot housings, joint areas and internal structures must handle repeated loads, vibration, flame requirements, electrical insulation and lightweighting.
200MPa
PPS tensile
13.5GPa
flexural modulus
0.02%
PPS water absorption
V-0
FR direction
Operating conditions
Four critical conditions for Robotics
Each section follows the failure path for this application. Final targets depend on part design, wall thickness and the customer test plan.
02
toughness
Impact and drops
Mobile and service robots face collisions, drops and transport impacts.
Balanced stiffness
03
V-0 + insulation
Electrical compartment
Battery, control and harness zones require flame, low absorption and electrical stability.
V-0 / CTI
04
chemical resistance
Cleaning
Housings contact detergents, oils and disinfectants while maintaining appearance and dimensions.
Low absorption
Recommended materials
Recommended grades and data for Robotics
Data is sourced from product pages and technical documents. The series, suffix, color and thickness must be locked in the controlled TDS.
Rigidity route
S265G8
PPS + 40%GF · High-rigidity frames and internal structures
Key data
Rigidity route
S265G8
PPS + 40%GF · High-rigidity frames and internal structures
- Tensile
- 200 MPa
- Flexural modulus
- 13,500 MPa
- HDT
- 265°C
- Water absorption
- 0.02%
- Impact
- 50 kJ/m² @23°C
The product page points to industrial automation and equipment frames.
Structural option
A63V0GV20
FR PA66 + 20%GF · Motor brackets and structural connections
- Flame
- V-0 @1.5 mm
- Reinforcement
- 20%GF
- Properties
- high rigidity, heat resistance
- System
- halogen-free / red-phosphorus-free
A more broadly processable structural option than glass-fiber PPS; confirm toughness by formulation.
Low-absorption option
PX54F0HR
Modified PPO / PPE · Sensor bays, controls and housings
- Flame
- UL94 V-0
- Water absorption
- <0.1%
- Electrical
- low dielectric loss
- Compliance
- RoHS / REACH / ELV / FDA
For dimension-sensitive internal housings with electrical insulation needs.
S265G8 · Source: content-inventory: S265G8 product page
A63V0GV20 · Source: content-inventory: A63V0GV20 product page
PX54F0HR · Source: content-inventory: PX54F0HR product page
Validation & certification
Validate rigidity, impact and electrical stability by part
Housings, frames, motor mounts and electrical compartments should use different material profiles.
13.5 GPa
Rigidity
S265G8 flexural modulus for frames.
265°C
Heat
S265G8 HDT at 1.8 MPa.
50 kJ/m²
Impact
S265G8 23°C Charpy impact; notched 12 kJ/m².
0.02%
Dimensions
S265G8 water absorption; PX54F0HR below 0.1%.
ISO9001:2015IATF16949RoHSREACH
Public data and certificates do not replace project validation. Results apply only to the tested grade, color, thickness, specimen and conditions.
Technical data request
Request the controlled TDS for S265G8
Share the part, operating conditions and targets. A specialist will verify suffix, thickness, regulations and test conditions before sending the document.
Application inquiry
Discuss Robotics with our team
More complete inputs move the project faster into sample and validation work.
- Robot type and environment
- Loads and mounting
- Battery/control flame needs
- Drop and vibration tests
Need general material guidance or company information?