01
high CTI
Tracking risk
Outdoor moisture and contamination demand stable insulation and tracking resistance.
CTI 600V / PLC0
SOLAR PV
High-CTI weathering PC for PV connectors
CM9610S-BK3A475 targets PV connectors with CTI 600V / UL PLC0, low-temperature ductility, F1 weathering and validated dual-85 performance.
600V
CTI / UL PLC0
1500H
dual-85 aging
-40°C
low-temperature ductility
V-0
@1.2 mm
Operating conditions
Four critical conditions for Solar PV components
Each section follows the failure path for this application. Final targets depend on part design, wall thickness and the customer test plan.
02
UV and F1
Outdoor weathering
PV components need long-term UV stability with retained mechanical and electrical performance.
F1
03
-40°C ductility
Cold installation
Cold-climate installation and impact require ductility below freezing.
-40°C
04
UL 94 V-0
Thin-wall FR
Compact connectors require flame retardancy at 1.2 mm.
V-0 @1.2 mm
Recommended materials
Recommended grades and data for Solar PV components
Data is sourced from product pages and technical documents. The series, suffix, color and thickness must be locked in the controlled TDS.
Primary route
CM9610S-BK3A475
High-performance FR PC · PV connector
Key data
Primary route
CM9610S-BK3A475
High-performance FR PC · PV connector
- CTI
- 600V / UL PLC0
- Low temperature
- -40°C ductility
- Weathering
- F1
- Flame
- V-0 @1.2 mm
- Dual 85
- 1500H
- Sealing / IPT
- 1.5kV IP67
Designed for PV connectors; the published case reports more than 20% potential cost reduction versus PAGF/PPE routes.
Weathering option
PX54F0HR
Modified PPO / PPE · Connectors and 5G structures
- Flame
- UL94 V-0
- Water absorption
- <0.1%
- Electrical
- low dielectric loss
- Compliance
- RoHS / REACH / ELV / FDA
Low water absorption supports dimensional and dielectric stability in humid environments.
Hydrolysis option
CFR3010
FR PC/ABS · PV equipment structures
- Flame
- UL 94 V-0 direction
- Dual 85
- 1000H
- Impact after aging
- above 10
The site article also identifies this dual-85 route for PV applications; revalidate for each housing.
CM9610S-BK3A475 · Source: content-inventory: solar PV article
PX54F0HR · Source: content-inventory: PX54F0HR product page
CFR3010 · Source: content-inventory: CCS dual-85 article
Validation & certification
Validate electrical, environmental and flame performance together
A single flame rating does not cover PV reliability. CTI, cold ductility, UV, wet heat and sealing belong in one test plan.
CTI 600V
Tracking
UL PLC0 direction for the connector.
1500H
Wet heat
85°C / 85% RH performance retention.
1.5kV
Sealing / voltage
Published IP67 and IPT-related requirement.
F1
Weathering
UV and outdoor exposure stability.
ISO9001:2015IATF16949RoHSREACH
Public data and certificates do not replace project validation. Results apply only to the tested grade, color, thickness, specimen and conditions.
Technical data request
Request the controlled TDS for CM9610S-BK3A475
Share the part, operating conditions and targets. A specialist will verify suffix, thickness, regulations and test conditions before sending the document.
Application inquiry
Discuss Solar PV components with our team
More complete inputs move the project faster into sample and validation work.
- Connector geometry and wall
- Voltage and CTI target
- UV and wet-heat duration
- Cold impact requirement
Need general material guidance or company information?