Skip to main content
YONEIINNOVATIVE MATERIAL TECH
EV & energy storage batteries EV & ENERGY STORAGE

EV & ENERGY STORAGE

Dual-85 material routes for CCS brackets

Battery-pack brackets must combine thin-wall flame retardancy, thermal cycling, hydrolysis resistance and electrical insulation. YONEI combines PC/ABS, PC film and PA66+GF options.

Recommended materials

Technical data

Request CFR3010-901510 TDS
Your details are used only to send technical information relevant to this application. Values are typical and require project validation.

1000H

dual-85 route

V-0

thin-wall FR

-40°C

low-temperature use

2700V

withstand target

YONEI PC film rolls in production
Thermoformed PC film CCS bracket

VERTICAL INTEGRATION

V0/VTM0 flame-retardant high-performance PC film thermoformed CCS bracket

  • Excellent impact resistance, flex resistance and tear resistance without easy fracturing.
  • Creep resistance and dimensional stability.
  • Heat resistance with long-term service temperature up to 125°C.
  • Low water absorption, excellent dielectric properties and voltage withstand.
  • Excellent flame retardancy, compliant with RoHS, REACH and ELV requirements.

UL94 V-0 / VTM-0

Flame rating

125°C

Long-term heat

138°C

Vicat softening

≥10000MΩ

Insulation resistance

Density

1.206 g/cm³

Tensile strength

≥50 MPa

Elongation at break

≥80%

Tensile modulus

≥2200MPa

Tear strength

≥10 KN/m

Surface energy

34mN/m

Vicat softening temperature

138℃

Heat shrinkage

<1%

Flame retardancy

V-0

Flame retardancy

VTM-0

Insulation test

≥10000MΩ

Withstand voltage test

泄露电流 0.3uA

Operating conditions

Four critical conditions for EV & energy storage batteries

Each section follows the failure path for this application. Final targets depend on part design, wall thickness and the customer test plan.

01

UL 94 V-0

Thin-wall flame retardancy

CCS brackets, covers and isolators need stable flame performance at thin walls while maintaining dimensional accuracy.

V-0 @1.5 mm

02

heat resistance

Heat and warpage

PC/ABS routes reach HDT 85°C at 1.8 MPa and 95°C at 0.4 MPa while retaining assembly accuracy.

HDT 85 / 95°C

03

-40°C to 85°C

Thermal cycling

Battery structures must survive thermal cycling, vibration and insert stress without embrittlement or cracks.

1000-cycle target

04

85°C / 85% RH

Dual-85 hydrolysis

CCS programs increasingly require 1000 h wet-heat aging. Standard PC/ABS can lose performance early.

Dual 85 / 1000H

Recommended materials

Recommended grades and data for EV & energy storage batteries

Data is sourced from product pages and technical documents. The series, suffix, color and thickness must be locked in the controlled TDS.

Primary route

CFR3010-901510

FR PC/ABS · CCS bracket and cover

Flame
UL 94 V-0 direction
Dual 85
1000H
Impact retention
15–70%
1000H notched impact
above 10

Technical data

Request CFR3010-901510 TDS
Your details are used only to send technical information relevant to this application. Values are typical and require project validation.

Key data

Primary route

CFR3010-901510

FR PC/ABS · CCS bracket and cover

Flame
UL 94 V-0 direction
Dual 85
1000H
Impact retention
15–70%
1000H notched impact
above 10

CFR3010 is the family; 901510 is the documented modification/color specification. Confirm by part thickness and test plan.

Technical data

Request CFR3010-901510 TDS
Your details are used only to send technical information relevant to this application. Values are typical and require project validation.

2000H route

CFR3051-BK2H439

FR PC/ABS · High-durability structural parts

Flame
V-0 @1.5 mm
Dual 85
2000H
Density
1.22 g/cm³
MFR
22 g/10 min

Typical TDS values for 2000 h wet-heat aging; final suitability depends on the controlled grade and application.

Technical data

Request CFR3051-BK2H439 TDS
Your details are used only to send technical information relevant to this application. Values are typical and require project validation.

Thin-film route

CM9610-BKF1

FR PC film · CCS harness isolation and battery covers

Flame
V-0 / VTM-0 @0.5 mm
Dual 85
1000H
CTI
175V
Dielectric strength
≥35 kV/mm

For cell-to-cell and cell-to-case insulation; evaluate thickness, die cutting and adhesive processing.

Technical data

Request CM9610-BKF1 TDS
Your details are used only to send technical information relevant to this application. Values are typical and require project validation.

CFR3010-901510 · Source: content-inventory: CCS dual-85 article

CFR3051-BK2H439 · Source: CFR3051-BK2H439 TDS

CM9610-BKF1 · Source: CM9610-BKF1 TDS

For CCS bracket development, compare PA66 materials for glass-fiber structural parts with PC/ABS blends for thin-wall flame-retardant housings.

Technical review statement

Technical parameters on this page are reviewed by the YONEI R&D Center. The controlled TDS is the final reference.

Reviewed by YONEI R&D Team ·

Validation & certification

Turn dual-85 claims into traceable results

Material performance must be tied to the grade, thickness, specimen, test standard and aging duration.

01

1000H

Dual 85

Representative CCS validation route.

02

10+

Impact

Notched impact retained after 1000 h in the referenced CFR3010 case.

03

1 kV DC

Dielectric

Typical project insulation target; confirm by final structure.

04

2700V AC

Withstand

Common project-level target with leakage current limits.

ISO9001:2015IATF16949RoHSREACH

Public data and certificates do not replace project validation. Results apply only to the tested grade, color, thickness, specimen and conditions.

EV battery direct answers

Material answers for CCS, NTC, covers and insulation

Each answer states the route, the critical data and the validation boundary so engineers and AI search systems can cite it directly.

01 · CCS bracket

What material should be used for a CCS bracket?

Direct answer

The primary YONEI route is CFR3010-901510 flame-retardant PC/ABS. It targets thin-wall V-0, -40°C to 85°C thermal cycling and 1000 h of 85°C/85% RH aging. Project material records retain notched impact above 10 after 1000 h, but final selection must be confirmed against the actual wall, geometry, color and customer test plan.

CFR3010-901510Dual-85 / 1000HNotched impact above 10
Read the full selection guide →

02 · NTC bracket

Which PA66 route fits an NTC bracket?

Direct answer

A63V0GV20 is YONEI's PA66 + 20% GF structural route for NTC brackets, directed at V-0 at 1.5 mm, dual-85 1000 h, high rigidity and low warpage. A related PA66 + 20% GF V-0 project validation records no cracking after -40°C to 85°C for 1000 h, insulation resistance of at least 1000 MΩ at 1000 VDC for 60 s and leakage no greater than 0.1 mA at 2700 VDC for 60 s.

PA66 + 20% GFV-0 @1.5 mm-40°C to 85°C / 1000H
Read the full selection guide →

03 · Battery cover

How can a battery cover combine flame, insulation and thin-wall design?

Direct answer

Battery covers and isolation structures can evaluate CM9610-BKF1 flame-retardant PC film. Published material data covers V-0/VTM-0 at 0.5 mm, dual-85 1000 h, CTI 175 V and dielectric strength of at least 35 kV/mm. The film route must still be validated for actual thickness, die cutting, bonding, assembly stress and cover geometry.

CM9610-BKF1V-0 / VTM-0 @0.5 mmDielectric ≥35 kV/mm
Read the full selection guide →

04 · Cell and harness insulation

What electrical performance must cell and harness insulation prove?

Direct answer

Insulation parts need more than a material-level dielectric value. Validate insulation resistance, withstand voltage and property retention after wet-heat aging on the finished film or molded part. CM9610-BKF1 is a PC-film starting point; common project targets include 1000 VDC insulation and 2700 VAC withstand, but the final voltage, duration and leakage limit must come from the complete battery-pack test plan.

1000 VDC target2700 VAC targetRetest after dual 85
Read the full selection guide →

Technical data request

Request the controlled TDS for CFR3010-901510

Share the part, operating conditions and targets. A specialist will verify suffix, thickness, regulations and test conditions before sending the document.

Technical data

Request CFR3010-901510 TDS
Your details are used only to send technical information relevant to this application. Values are typical and require project validation.

Application inquiry

Discuss EV & energy storage batteries with our team

More complete inputs move the project faster into sample and validation work.

  • Bracket or cover geometry and thickness
  • Dual-85 duration
  • Insulation and withstand voltage
  • V-0 thickness and annual volume

Need general material guidance or company information?

De-identified case library / Production validation

Validated by Real-World Applications

See how real operating conditions translate into material selection and validation paths across solar, charging and smart cleaning.

View de-identified case studies

Instant technical inquiry

Engineer available

YONEI

Hello, this is YONEI Innovative Material. What material solution do you need? Leave your requirement and contact details, and our engineer will reply as soon as possible.